Language
deutsch
english
français
nederlands
italiano
dansk
svensk
Home
General safety instructions
Meaning of the text formatting
SmartIntego Tech Kit
Planning a SmartIntego project
Check conditions on site
Measure doors
Illuminate WaveNet
Components required
Measure test by test
Operation:
Identify potential eye-catchers
Ordering components
Planning the installation process
TCP: Installation according to WaveNet illumination
TCP: On-site installation (automatic WaveNet configuration)
TCP: On-site installation (manual WaveNet configuration)
TCP: Prepared installation (construction site whitelist)
TCP: Prepared installation (Integrator Whitelist)
RS-485: On-site installation (manual WaveNet configuration)
RS-485: Prepared installation (construction site whitelist)
Commissioning the SmartIntego project
Creating, expanding and importing a name list
Create door name list
Expand door name list
Importing a door name list into SmartIntego Manager
Document system
Install SmartIntego tool
Update SmartIntego tool (WO)
Changes to SI-Tool 3.0
Changes to SI-Tool 3.1
Createing a SmartIntego project
Create, modify and delete construction site whitelist
Create construction site whitelist
Change the construction site whitelist
Delete the construction site whitelist
Card configuration setup
Unique ID mode
Card data usage mode: MIFARE Classic
Card data usage mode: MIFARE DESFire
Entering card data
Protecting card configuration
Creating and loading a template for card configurations
Create template (integrator)
Load template (installer)
Set coupling duration
Configuring GatewayNodes (TCP)
Search GatewayNode
OAM tool
Determining and setting the IP address
Browser interface
Updating firmware
Open configuration page
Assign IP address
Change the password of the configuration website
Set GatewayNode encryption
About IEEE802.1X
Disable Telnet Access
Disable HTTP access (unencrypted)
Disable OAM tool access
TCP Keep Alive (set timeout)
Update GatewayNode
RS-485 ConfigNode
Configure RS-485 ConfigNode
Configure RS-485 ConfigNode for another project
Use RS-485 ConfigNode in various projects
Setting up SmartIntego Manager
WaveNet global settings
Add GatewayNode
TCP: Add individual GatewayNodes
TCP: Add multiple GatewayNodes (IP range)
TCP: Add multiple GatewayNodes (Broadcast)
TCP/RS-485: Add Radio Radio Gateway Node
RS-485: Add individual GatewayNodes
RS-485: Add multiple GatewayNodes
Add LockNodes
Add individual LockNodes
Add multiple LockNodes (Manual)
Add multiple LockNodes (Automatic)
Programme locking device
Programme hybrid locking devices
Programme hybrid locking devices
SmartHandle: Configure DoorMonitoring
SmartHandle: Configure Escape&Return
Configure PIN code keypad
Changing the master PIN
Determining the PIN length
Setup
Configure Node IO
Managing locking devices in the SmartIntego tool (WO)
Check WaveNet
Automatically assign LockNodes
Connecting SmartIntego to the integrator system
Maintain SmartIntego project and correct errors
Read access list (whitelist accesses)
Read access list via WaveNet
Read access list via programming device
Time in the locking device
Setting the time on a single locking device
Setting the time on several locking devices
Change DNS name or IP address of a GatewayNode
Rename GatewayNode
Renaming an individual GatewayNode
Rename multiple GatewayNodes
Replace GatewayNode
Replace defective locking device
Replace intact locking device
Relocate locking devices (assign to another GatewayNode)
Move individual locking device
Moving several locking devices
Restructuring the system
Carry out emergency opening
Battery change and battery replacement card
Creating a battery replacement card
Battery replacement
Engage locking device in the event of a network failure
Disengage locking device in the event of a network failure
Creating and using WaveNet test cards
Create WaveNet test card
Use WaveNet test card
Programming with the local programming device
Reset components
Resetting components with SmartIntego software
Re-set locking device
Resetting the LockNode
Resetting GatewayNode
Resetting components with hardware reset
Resetting the programmed LockNode and programmed locking device
Resetting the programmed LockNode and non-programmed locking device
Resetting the WaveNet/network configuration of the GatewayNode
Hardware reset of external LockNodes
PIN code keypad
Set to storage mode
Create and restore backup
Create backup
Restore backup
Changelog
Help and other information
Home
Commissioning the SmartIntego project
Update SmartIntego tool (WO)
Changes to SI-Tool 3.1
Changes to SI-Tool 3.1 - Step-by-Step WO
Support for the
SI Digital Cylinder AX