Installing the fitting - SmartHandle AX Advanced
- Door pre-drilled.
- Blind rivet nut pliers at hand.
- PH2 screwdriver at hand.
- TX15 screwdriver at hand.
- Caliper gauge at hand.
- Fit the blind rivet nuts into the pre-drilled holes.
- For non-MO: insert the blank cylinder.
NOTE
Feed the blank cylinder into the hole using a screwdriver
It is difficult to position the blank cylinder correctly, especially in thick doors.
- Insert a screwdriver into the hole in the blank cylinder.
- Position the blank cylinder using the screwdriver.
- For non-MO: screw the dummy cylinder firmly into place (PH2; torque: 1.1 Nm).
- Use the 12 mm screws to fix the fastening plate onto the outer side of the door with the tip facing upwards (PH2, torque 3.0 Nm).
- Insert the module support into the fastening plate.
- Slide the module support upwards.
- Module support snaps into place.
- Use the 18 mm screws to fix the module support onto the fastening plate (PH2, torque 3.0 Nm).
- Place the cover on top of the fastening plate.
- Fold down the cover.
- Push the cover against the door, sliding it upwards at the same time.
- Cover snaps into place.
- Press the inlay into place.
- Fit the outside handle.
- Determine the required direction of rotation for your inside handle.
- Insert the spring element appropriately.
- Place the underlay in the inside handle unit.
- For 8.5 mm and 10 mm spindle: slide the adapter sleeve into the centre of the spindle. Use a punch and hammer to make an indent in the adapter sleeve to prevent it from slipping.
- Measure the total length of the spindle.
- Locate the inside of the spindle (four-edge end up to the centre of the first groove = 26 mm).
- Use the table to determine the position of the O-ring.
Area
Door thickness (mm)
Spindle length (mm)
Ring position
S
38 – <42
94
3
S
38 – <42
104
5
S
42 – <47
94
2
S
42 – <47
104
4
S
47 – <52
94
1
S
47 – <52
104
3
S
52 – <57
104
2
S
57 – 60
104
1
M
58 – <62
114
3
M
58 – <62
124
5
M
62 – <67
114
2
M
62 – <67
124
4
M
67 – <72
114
1
M
67 – <72
124
3
M
72 – <77
124
2
M
77 – 80
124
1
L
78 – <82
134
3
L
78 – <82
144
5
L
82 – <87
134
2
L
82 – <87
144
4
L
87 – <92
134
1
L
87 – <92
144
3
L
92 – <97
144
2
L
97 – 100
144
1
XL
98 – 184
O-ring is 30–35 mm from the cut end of the spindle.
- Slide the O-ring onto the calculated groove.
- Insert the spindle into the door with the ring-free side as far as it will go.
- Place the inside handle unit on the spindle.
- Use the 22 mm screws to fasten the inside handle unit onto the inner side of the door (PH2, torque 3.0 Nm).
- Use the 16 mm screws to fasten the cylinder rosette on the inner side of the door (PH2, torque 1.1 Nm).
- Use the grub screws to tighten both handles (TX15, torque 5.0 Nm).
- Place the cylinder plate and the inside handle cover onto the escutcheons.
- SmartHandle AX Advanced fully installed.
